We installed a truck bed cover onto 2022 Ford F150 Raptor. The cover was manufactured by Retrax, part #T-80378. This is the XR cover, meaning this cover is equipped with channels in the side rails allowing for mounting accessories. This installation required us to build the system prior to putting it into the truck bed and secure it by clamping the rails onto the vehicles existing side rails. We also drilled drain holes into the bed of the vehicle where directions specified for drain plugs of the cover. A second pair of hands would be highly recommended for this installation.
We installed a canopy onto a 2022 Ram 2500. The RSI SmartCap is one of the strongest canopies in the industry constructed from steel it can support up to 330lbs of payload when moving, 770lbs when parked. This is the EVOa Adventure model which features double-walled stainless steel Gullwing doors with interior MOLLE panels for mounting your gear. The assembly and installation for this canopy is difficult and requires multiple trained specialists.
We installed crossbars and a cargo box onto a 2021 Ford Explorer. The crossbars and cargo box were manufactured by Yakima. The crossbars are known as the Timberline system and are made up of the Timberline towers and Corebar crossbars, this system attaches by wrapping around the vehicles existing elevated siderails. Attached to the crossbars is the Skybox 16 cargo box which provides 16 cubic feet of storage, integrated tie-downs, locks, and the ability to open from both sides.
We installed crossbars onto a 2022 Toyota Tacoma. The crossbars were manufactured by Yakima and attach to the vehicle by clamping around the door frame and weather stripping. The crossbars are made up of a set of Yakima Baseline towers, Yakima Corebars, Baseclip 145 (front bar), Baseclip 128 (rear bar). This crossbar setup has a weight load capacity rating up to 165lbs.
We installed a platform backbone system onto a 2021 Jeep Gladiator. The platform backbone system was manufactured by Rhino Rack. This installation required us to drill into the hardtop of the vehicle and install metal supports on the inside that line up with the roof fixtures to go where the feet are positioned on the platform. The Pioneer Platform is made up of multiple slats that have a channels which run through the middle of each piece to allow for mounting of future accessories.
We installed crossbars and an awning onto a 2000 Volkswagen Eurovan. The crossbars were manufactured by Rhino Rack and the awning by Thule. To install the crossbars we had to drill into the vehicles existing roof ditches and install rivet nuts to allow for the feet to attach. The feet we used were Rhino Rack's RLT600 and paired them with the VA150B crossbars. These crossbars have a channel that runs the length of the bars to allow for mounting of accessories such as an awning. The Thule Outland awning is 7.5ft long and extends out 8ft. with push-button operation it allows for easy, one person setup.
We installed track and crossbars onto a 2010 Ford Ranger. The roof rack system we found that works best for fiberglass canopies is made by Rhino Rack. This installation required us drill through the canopy and install the track using bolts, nuts and silicone sealant. Once attached, the feet that we used are Rhino Racks RLT 600's paired with VA 165B crossbars which have channel mount capability for mounting of accessories. The weight capacity for this setup on the canopy is rated for 165lbs.
We installed a ladder onto a 2021 Toyota 4runner. The ladder was manufactured by Frontrunner Outfitters and it came unassembled. The ladder is constructed of black powder coated high strength steel.
We installed a platform and backbone system onto a 2017 Jeep Wrangler. The setup was manufactured by Rhino Racks and is supported by their Backbone system. This installation required us to drill into the hardtop of the vehicle and install metal supports on the inside that line up with the roof fixtures to go where the feet are positioned on the platform. The platform is made up of multiple slats that have a channels which run through the middle of each piece to allow for mounting of future accessories.
We installed crossbars and an awning onto a 2021 Ford Transit 250. The crossbars were manufactured by Thule and are known as TracRac Van ES rack system. These crossbars attached into the vehicles existing fixed points on the roof. Attached to the crossbars is the Thule Hideaway awning, this is the 10ft model meaning you get 10 feet long and 8 feet wide of self-supported shade.