NOTICE: WE DO NOT SHIP

In Store Pick-Up in Bend, Oregon

rhinorack

  1. 2022 Jeep Wrangler - Winch, Platform, Sidesteps - Warn / Rhino Rack / RockSlide Engineering

    We installed a winch, backbone platform system, and sidesteps onto a 2022 Jeep Wrangler. The winch was manufactured by Warn Industries using parts # 87310, 100650 and 101255. This installation was tedious and required us to take apart the entire front bumper to attach the winch and make sure the electrical components work. This was no easy process and required multiple hours of work from our trained specialists. The platform setup was manufactured by Rhino Rack and is supported using their Backbone system. This installation required us to drill into the hardtop of the vehicle and install metal supports on the inside that line up with the roof fixtures to go where the bases are positioned. Attaching to the bases is the pioneer platform that has channels that run the length of the slates for mounting of accessories such as the ones pictured (sunseeker awning, hi-lift jack, recovery boards). This installation
    Read more »
  2. 2018 Chevrolet Colorado - Crossbars and Backbone Platform - Rhino Rack

    We installed crossbars and a backbone platform onto a 2018 Chevrolet Colorado. All products involved are manufactured by Rhino Rack. The crossbars were installed over the cab of the vehicle using Quick Mount Ditch Bracket part #QMFK08, Quick Mount Leg part #RLT600, and Vortex Bars part #VA126B. Attached to the crossbars is the XTray Large basket that has a load capacity rating of 165lbs. Installation of the Backbone Pioneer Platform system was made up of two parts; the Backbone Rails #RUMB1, and the Pioneer Platform part #52102F. Both of these installations required us to drill into either into the vehicle or the canopy and should be done by trained specialists.
    Read more »
  3. 2012 Toyota Tacoma - Platform and Accessories - Rhino Rack / Maxtrax

    We installed a pioneer platform and accessories onto a 2012 Toyota Tacoma. The pioneer platform was manufactured by Rhino Rack and attached to the canopy's pre-existing tracks. Inside the slats of the pioneer platform features a channel that allows for mounting of accessories such as the Rhino Rack Stow-It shovel/axe holder, Maxtrax vehicle recovery device, and the Rhino Rack Sunseeker awning. This installation was tedious and requires a second pair of hand to help lift the platform onto the vehicle.
    Read more »
  4. 2022 Jeep Wrangler - Crossbars and Backbone - Rhino Rack

    We installed crossbars and backbone system onto a 2022 Jeep Wrangler. The setup was manufactured by Rhino Racks and is supported by their Backbone system. This installation required us to drill into the hardtop of the vehicle and install metal supports on the inside that line up with the roof fixtures to go where the bases are positioned. Attached to the bases are RLT600 feet and VA150B crossbars. This installation should be done by trained specialists.
    Read more »
  5. 2017 Toyota Tacoma - Awning - Rhino Rack

    We installed an awning onto a 2017 Toyota Tacoma. The Sunseeker 2.5m awning manufactured by Rhino Rack product # 32133, measures 87 in. High, 98 in. Long, and 83 in. Wide. This awning provides up to 55.38 sq ft shaded area for you and your family to relax in. It is attached to the vehicle by with t-bolt hardware that slides into Rhino Racks Vortex Crossbars accessory channels.
    Read more »
  6. 2021 Jeep Gladiator - Platform and Backbone - Rhino Rack

    We installed a platform backbone system onto a 2021 Jeep Gladiator. The platform backbone system was manufactured by Rhino Rack. This installation required us to drill into the hardtop of the vehicle and install metal supports on the inside that line up with the roof fixtures to go where the feet are positioned on the platform. The Pioneer Platform is made up of multiple slats that have a channels which run through the middle of each piece to allow for mounting of future accessories.
    Read more »
  7. 2000 Volkswagen Eurovan - Crossbars and Awning - Rhino Rack / Thule

    We installed crossbars and an awning onto a 2000 Volkswagen Eurovan. The crossbars were manufactured by Rhino Rack and the awning by Thule. To install the crossbars we had to drill into the vehicles existing roof ditches and install rivet nuts to allow for the feet to attach. The feet we used were Rhino Rack's RLT600 and paired them with the VA150B crossbars. These crossbars have a channel that runs the length of the bars to allow for mounting of accessories such as an awning. The Thule Outland awning is 7.5ft long and extends out 8ft. with push-button operation it allows for easy, one person setup.
    Read more »
  8. 2010 Ford Ranger - Track and Crossbars on Canopy

    We installed track and crossbars onto a 2010 Ford Ranger. The roof rack system we found that works best for fiberglass canopies is made by Rhino Rack. This installation required us drill through the canopy and install the track using bolts, nuts and silicone sealant. Once attached, the feet that we used are Rhino Racks RLT 600's paired with VA 165B crossbars which have channel mount capability for mounting of accessories. The weight capacity for this setup on the canopy is rated for 165lbs.
    Read more »
  9. 2015 Nissan Frontier - Crossbars and Kayak Rack - Yakima

    We installed crossbars and kayak racks onto a 2015 Nissan Frontier. The crossbars were manufactured by Rhino Rack and attach to the vehicle by clamping around the door frame and weather stripping. The crossbars are made up of Fitting Kit DK108, 2500 Legs and Vortex Bars VA137B. Attached to the crossbars are the Yakima Sweet Roll kayak carriers that feature rear saddles with integrated rollers for easy loading.
    Read more »
  10. 2015 Ram 1500 - Track and Crossbars on canopy, plus 1 bar over cab

    We installed track and crossbars onto a fiberglass canopy as well as one bar over the cab of a 2015 Ram 1500. The roof rack system we found that works best for fiberglass canopies is made by Rhino Rack. This installation required us drill through the canopy and install the track using bolts, nuts and silicone sealant. Once attached, the feet that we used are Rhino Racks RLT 600's paired with VA 165B crossbars which have channel mount capability for mounting of accessories. The weight capacity for this setup on the canopy is rated for 165lbs. We also installed a crossbar over the cab of the vehicle. This bar was also manufactured by Rhino Rack and mounted into the vehicles ditch mount. A spacer was attached to the feet of this crossbar to raise the height of the bar to match with the height of the crossbars from the canopy.
    Read more »
Page